Two-component clear silicone potting compound for electronic component
∎Product Description
●SI8125A/B is used in potting protection of varied components. It can vulcanize to deep layer. The two components have a good fluidity after mixing. The operation time can be adjusted with the proportion of hardener part B. It can bond well with most materials without using any primer. It can be used to fix the accessories to resist water, dust and leakage of electricity.
.
∎Typical Applications
●Used for Automotive electronics, modules like Power control modules, Solar modules, Junction box, LED spotlight, Wall washer light, Strip lights, LED fluorescent lamp, etc.
∎Technical Data Table
| PROPERTY | UNITS | PART A | PART B | |||||||||||
| ---- | ---- | 8125T | 8125M | 8125W | 8125W-1 | 8125B | 8125T | 8125 | ||||||
| Color | Visual inspection | Colorless transparent fluid | Matte transparent white fluid | White fluid | White low viscosity fluid | Black fluid | Colorless fluid | Colorless fluid | ||||||
| Viscosity | 25°C, cps | 1,300 | 1,800 | 3,500 | 2,100 | 2,100 | 50 | 50 | ||||||
| Density | 25°C, g/cm3 | 1.02 | 1.03 | 1.18 | 1.18 | 1.18 | 0.98 | 0.98 | ||||||
| Corresponding curing agent (Part B) | 8125T | 8125T | 8125 | 8125 | 8125 | --- | --- | |||||||
| Mixture/mass ratio | ---- | A:B=100: (10±3) | ||||||||||||
| Viscosity of mixture | 25°C, cps | 1,000 | 1,000 | 2,300 | 1,500 | 1,500 | --- | --- | ||||||
| Operation time | 25°C, min | 40 | 40 | 40 | 50 | 40 | --- | --- | ||||||
| The operation time can be adjusted with the proportion of hardener part B. | ||||||||||||||
| Surface hardening time, min | 70~180 | |||||||||||||
| Characteristics after curing | ||||||||||||||
| Cured appearance | ---- | Colorless transparent elastomer | Matte white elastomer | White elastomer
| White elastomer | Black elastomer | --- | --- | ||||||
| Hardness | Shore A | 21 | 21 | 28 | 15 | 12 | --- | --- | ||||||
| Tensile strength | MPa | 1.0 | 1.0 | 1.2 | 1.2 | 1.2 | --- | --- | ||||||
| Shear strength | MPa | 0.3 | 0.3 | 0.7 | 0.7 | 0.7 | --- | --- | ||||||
| Loss factor | 1 MHz | ＜0.008 | ||||||||||||
| Dielectric strength | kV/mm, 25°C | ≥20 | ||||||||||||
| Volume resistance | DC500V, Ω·CM | 1.1×1015 | ||||||||||||
| Dielectric constant | 1 MHz | ＜3.00 | ||||||||||||
| Long-term apply temperature | °C | -50~150 | ||||||||||||
Note:All above data were tested under standardized condition, or tested by further experiments.
∎Key Features
-
●Two-component high transparency liquid silicone rubber, condensation dealcoholization type
●Low viscosity, easy to process and operate
●Low hardening condensation, no corrosion and stressless
●Excellent electric insulativity and stability in high temperature
●Excellent bonding ability, good water-proof and moisture-proof property
∎Packing Specification
●Part A—20 KG/Bucket
●Part B—2 KG/ Bucket.
20kg per set
∎Transport &Storage
● When stored at or below 25°C in the original unopened containers, this product has a usable life of 12 months from the date of production. Sampling test is necessary for products which exceed shelf life before taking use.
It’s non-dangerous goods, can be transported as normal chemicals, CAUTION leakage during transport.
.∎Directions for Use
-
Mix Part A and Part B by 100:10 mass ratio, after evenly mixed, pouring directly into the components or modules as per requirements. It’s recommended to slowly pour along the walls of the implements, so as to reduce the bubbles happens.
Still the potted component to let out the bubbles. Vacuum defoaming process of the mixture before potting can improve the performance.
∎Attention of operation
●Keep away from Children
●Avoid contact with eyes and skin. If contact with your skin, scrub first with soap water or alcohol, then rinse with water. If contact with your eyes, rinse with plenty of water, and seek medical treatment immediately.
● It is forbidden to build on the surface of the wet substrate.
∎Safety Operation Data
MSDS isn't included here. Please read TDS, MSDS and label carefully before operation. You can get MSDS from MAXTECH or other distributors, or mail to service center maxtech@shmaxtech.com
∎Warranty and Liability
All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advice we supply don't apply in any circumstances. MAXTECH don't make assurance of any other applications outside the specification until MAXTECH supply a special written guarantee. MAXTECH is only responsible to replace or refund if this product is defective within the warranty period stated above. MAXTECH makes it clear that will not be liable of any accidents.
Any inquiry, welcome to talk more with us , contact us sally, sally@shmaxtech.com; +8618321208486
